Wicker Patio Dining Chairs: Top Picks Compared

The best wicker patio dining chairs pair a rust-proof frame with all-weather resin weave, a seat height near 17 to 19 inches and cushions you can pull off and dry. That combination slides under a standard 28 to 30 inch patio table and survives rain, sun and winter storage. This comparison covers ten sets of wicker patio dining chairs, sorted by frame, weave and how they stack or store, so you can match a set to your table instead of guessing from a photo.

Wicker Patio Dining Chairs Compared at a Glance

How We Chose

We did not personally use these chairs. This guide is built from maker listings, published dimensions and widely used outdoor furniture sizing rules, and it names only models with current listings. We kept sets that call themselves dining chairs, preferred weather-resistant frames, and capped each brand at two entries. Where a listing does not state a dimension, a coating, a fade rating or a weight, we say so and suggest checking the maker page, since outdoor furniture changes finishes and cushions between production runs. Prices are described in tiers only.

Christopher Knight Home Set of 2 Farley Patio Wicker Dining Chairs, Outdoor/Indoor Woven PE Rattan Accent Armless Chair, Sturdy Metal Frame Garden/Porch/Poolside/Backyard Side Chair, Dark Brown

Chosen because it specifies Outdoor/Indoor Woven PE Rattan Accent Armless Chair and Sturdy Metal Frame Garden/Porch/Poolside/Backyard Side Chair.

View on Amazon →

Christopher Knight Home Joan Handwoven PE Wicker Dining Chairs Set of 2, Weather-Resistant Armless Chairs Set, Outdoor Dining Chairs for Garden Backyard, Side Chairs for Patio Furniture Set, Natural

Chosen because it specifies Weather-Resistant Armless Chairs Set and Outdoor Dining Chairs for Garden Backyard.

View on Amazon →

Christopher Knight Home Joan Handwoven PE Wicker Dining Chairs Set of 4, Weather-Resistant Armless Chairs Set, Outdoor Dining Chairs for Garden Backyard, Side Chairs for Patio Furniture Set, Natural

Chosen because it specifies Weather-Resistant Armless Chairs Set and Outdoor Dining Chairs for Garden Backyard.

View on Amazon →

1. SAILARY All-Weather Dining Chairs Set of 4: Best Value Four-Pack

• Set of 4 outdoor wicker dining chairs with cushions
• 350 lb weight capacity, per the listing
• All-weather wicker
• Check the maker page for seat height and frame material

Best for: filling a four-person patio table in one order. Skip if: you need a chair with a documented seat height; the listing text does not state one, so measure against your table before ordering.

Pros: the stated weight capacity is on the high side for the category; four chairs per box lowers cost per seat; cushions are included.

Cons: no fade rating is stated in the listing text; cushions are not always machine washable, so look at the care tag; assembly time multiplies with four chairs.

2. SAILARY High-Back Club Chairs: Best for Lounging at the Table

• Porch-style rattan club chairs with padded cushions
• High back
• Sold as a set of 2 or a set of 4
• Check the maker page for seat height

Best for: long dinners where people linger. A higher back supports the shoulders better than a low-back café chair. Skip if: your patio table has a low apron; club-style chairs are chunky and may not tuck fully under.

Pros: plusher feel; two-chair option suits a bistro pair; same brand makes a matching four-pack.

Cons: bulkier, so they take more space on the patio; not stackable by default; the cushions soak up water if left out in rain.

3. DAYARUS Dining Chairs with Armrests: Best Metal-Frame Build

• Set of 4 outdoor dining chairs, wicker with cushions
• Metal patio chair frame with armrests
• Cushioned backrest
• A set of 2 is also sold

Best for: yards that see rain, since a metal frame is a better long-term base than bare wood. Skip if: your climate has salt air; check the maker page for the powder coat or galvanizing description, because bare steel rusts at screw points.

Pros: armrests that add comfort; a cushioned back; the metal frame is described plainly in the listing.

Cons: armchairs need a table with a clear gap; weight is higher than a resin-only chair; the set of 4 is among the pricier here.

4. UDPATIO Stackable Chairs with Armrests: Best for Storage

• Set of 4 stackable wicker outdoor chairs
• All-weather rattan weave
• Deep seat with armrests
• Stacks for winter storage

Best for: small patios and garages, since four chairs stack into a single column. Skip if: you need thick cushions; stackable designs usually trade cushion depth for a nesting shape.

Pros: easy to clear off the deck; low price tier; all-weather weave language in the listing.

Cons: thinner seat padding; armrest height can block stacking if cushions are fixed, so check the listing for cushion type; sold as 4 only.

5. JEAREY Stackable Rattan Chairs: Best Low-Cost Stackers

• Set of 4 stackable rattan chairs, brown
• Powder-coat frame, per the listing
• Outdoor dining chair styling
• Check the maker page for coating and weight limit

Best for: renters and casual users who want four chairs that live outside in summer and in a shed in winter. Skip if: you expect heavy daily use for years; budget stackers are better for occasional dining than for a main family table.

Pros: low cost per chair; powder-coated frame that shrugs off light rain; compact when stacked.

Cons: unconfirmed weight capacity; cushions minimal; the weave may show wear sooner at pressure points.

6. Tangkula Stackable Wicker Chairs: Best Mix of Wood and Metal

• Set of 4 stackable patio wicker dining chairs
• Outdoor rattan weave with acacia wood armrests
• Metal frame
• Check the maker page for stacking height

Best for: patios that want a more furniture-like look than a plain resin chair. Wood armrests feel warmer to the touch than metal. Skip if: you do not want to maintain wood; acacia armrests may need oiling or sealing, and the maker will have its own instructions.

Pros: mixed materials add style; metal frame and stackable design; the wood armrests are comfortable.

Cons: wood requires care; a bit heavier to stack; the finish may weather faster than coated metal.

7. VOYSIGN Dining Chairs Set of 2: Best Pair for a Bistro Table

• Set of 2 outdoor wicker dining chairs
• Rattan weave with removable cushions
• Restaurant-chair styling
• Check the maker page for frame material and size

Best for: a two-person balcony table. Removable cushions mean you can bring pads indoors. Skip if: you need to seat four or more; buy two sets and compare dimensions to be sure they match.

Pros: low cost; removable cushions; a simple design that does not overpower a small space.

Cons: sold in pairs only; little documented weight rating; light frames can tip if someone leans back.

Also Consider

• DAYARUS set of 2 with armrests: the same style as the four-pack, for a smaller table. Check that the backrest height matches your table.
• SAILARY set of 2 wicker chairs: a smaller, lower-cost pair of the same maker. Compare the cushions to the four-pack.
• Greesum 9-piece acacia patio dining set for 8: a table-and-chairs bundle with PE rattan chairs; useful if you need a whole set rather than only chairs.

Wicker Patio Dining Chairs: Resin vs Rattan Weave

The word wicker names a weaving technique, not a material, which is why one set can be called wicker, rattan or all-weather without being different. Natural rattan is a cane harvested from a palm; it looks good but dries, cracks and fades in sun and rain, so it belongs on a covered porch. The resin weave sold for outdoor use is a plastic fiber, often listed as PE rattan or all-weather wicker, wrapped around a frame. It does not absorb water and is made for outdoor life.

Weave quality shows in how tightly strands are wrapped and how the ends are tucked at the frame. Loose strands that stick out snag clothing and unravel first at the seat edge. A frame inside the weave decides longevity: steel with a powder coat and aluminum both resist rust better than bare steel.

Seat Height and Table Fit: The Numbers That Matter

Standard dining table height is 28 to 30 inches. The ideal seat height is 17 to 19 inches, which leaves 10 to 12 inches of thigh clearance between the top of the seat and the underside of the tabletop. Counter-height patio tables run about 36 inches and need chairs or stools with 24 to 26 inch seats; wicker patio dining chairs are not made for those.

For armchairs, measure arm height. If arms sit 25 inches off the ground and your table apron is 26 inches off the ground, the arms can slide under; if the apron is at 24 inches, they cannot. Without room to tuck in, the chairs stick out into the walkway. Stackable chairs tend to have lower arm heights for nesting, which makes them easy to tuck. Use a tape measure, not the picture.

Chair width matters for spacing: a typical dining chair is 20 to 25 inches wide, and you want 24 inches of table edge per seat. A 36 by 60 inch rectangular patio table seats six with armless chairs, while armchairs usually reduce that to four to five.

Cushion Fade Ratings and Fabric: What to Look For

Cushion fabric is the first thing that fails outdoors. Solution-dyed acrylic holds color best because the pigment goes through the fiber, while ordinary polyester prints can fade within a season in direct sun. A listing that mentions UV-resistant or fade-resistant fabric is better than one that is silent, but no listing here states a measured fade rating, so treat the claim as a general statement and look at the care tag. Cushion foam should be quick-dry or open cell, because standard foam holds water and gets moldy.

Practical rules: choose zippered covers you can remove and wash, store cushions indoors during long rain spells or winter, and pick mid-tone colors that show less fading and dirt than very dark or bright ones. Look for ties or straps so cushions do not slide off in the wind.

How Many Chairs Fit Which Patio Table

Match the chair count to the tabletop before you pick a set size. Chairs with arms need about 24 to 26 inches of table edge each, and armless chairs need 20 to 22 inches. That gives a simple guide you can check with a tape measure.

If you need six, remember that a set of 4 and a set of 2 from the same maker usually match, but check that the listing shows the same model and cushion color. Two different dye lots of cushions can look slightly different side by side, and sellers sometimes change cushion fabric between batches.

Common Mistakes When Buying Outdoor Wicker Chairs

• Buying by photo, not by seat height. A chair that looks right in a staged shot can be 20 inches high and press against the table apron.
• Ignoring the underside. Weave should cover the seat bottom; bare frames collect water and rust faster.
• Leaving cushions out. Even quick-dry foam takes a day or two to dry after a soak, and mildew starts in damp, shaded corners.
• Mixing sets from different makers. Heights, arm profiles and weaves differ, and the table ends up looking patched together.
• Skipping the bolt check. Assembly hardware loosens as the weave flexes; a wobble is almost always a loose bolt, not a failing chair.

One more point: wicker chairs sit in the sun, and dark frames and dark cushions get hot. In hot climates, lighter colors keep the seat cooler to the touch.

Styling and Comfort Upgrades for Wicker Dining Chairs

Wicker looks best when the rest of the patio stays simple. Pair brown or grey weave with a neutral table, then add color through seat pads, a runner or an outdoor rug. A rug under the table also protects the weave from scraping on concrete and keeps chair legs from sinking into gaps between deck boards. Choose a rug large enough that the back legs stay on it when chairs are pulled out, which usually means adding 24 inches on every side of the table.

For comfort, a seat pad with ties or a non-slip backing grips the weave better than a loose cushion. If the included cushion feels thin, a replacement in a quick-dry foam of two to three inches changes a short dinner chair into one people linger in. Match the replacement width to the seat opening, and measure depth from the backrest, not from the front edge. Wind is the other factor: a light wicker chair on a high balcony can slide or tip, so rubber glides on the feet and a clip or tie on the cushion are small fixes that help.

Buying Guide: Choose a Wicker Patio Chair Set Step by Step

1. Measure the table. Write down height, apron height and clear width per seat. Choose seat height 10 to 12 inches below the tabletop.
2. Decide on stackable or fixed. If you store chairs in winter, stackable saves space; if they stay out, thick cushions matter more.
3. Pick the frame. Powder-coated steel or aluminum beats bare steel. If the listing says only steel with no coating, expect rust at screw points in humid areas.
4. Check the weight limit. Look for 300 lb or above. One set here lists 350 lb; others do not state a number.
5. Inspect the weave. Tight wraps, no loose ends, full coverage on the underside of the seat.
6. Read the cushion care. Removable, zippered, quick-dry foam; avoid sets with sewn-on pads.
7. Plan assembly. Four-packs mean four assemblies so set aside an hour or more and check the box for tools.

When a set arrives, tighten bolts on day one and again after a month. Wicker seats flex with use, and loose bolts are the cause of wobble far more often than a flawed weave.

Care and Winter Storage

Rinse chairs with a garden hose and mild dish soap a few times per season, using a soft brush for the weave. Skip pressure washers, which can force strands apart. Dry the frame fully before covering, since trapped moisture rusts metal. Cushions should come indoors or go in a deck box before the first freeze. If you have no storage, fitted covers that tie at the hem protect chairs from rain and snow far better than a loose tarp. Stackable chairs can nest under a single cover, which is the main reason they suit small patios.

Frequently Asked Questions

What are the best wicker patio dining chairs for rain?

Look for resin or PE wicker over a powder-coated steel or aluminum frame, with removable cushions. The weave is the part that resists water; the frame coating protects against rust.

How high should patio dining chair seats be?

About 17 to 19 inches for a standard 28 to 30 inch table. Pick chairs that leave 10 to 12 inches between the seat and the tabletop.

Is rattan or resin better for outdoor dining chairs?

Resin. Natural rattan swells, cracks and fades outdoors, while resin weave is built for rain and sun. Use natural rattan only under cover.

Do wicker chairs fit under a patio table?

Armless ones usually do. Armchairs only tuck in if the arm height is lower than the table apron; measure both before you order.

How long do wicker patio chairs last?

It depends on frame coating, weave quality and cushion storage. Resin on a coated frame can last several seasons with basic care, while uncoated frames and unprotected cushions wear out first. Check the warranty on the maker page.

Can I leave wicker chairs outside in winter?

Resin chairs can handle weather, but snow load and ice can warp thin frames and stress the weave. Cover them or stack them under a fitted cover, and bring cushions inside.

Are stackable wicker chairs comfortable?

They are comfortable for dinner but usually thinner than lounge chairs. If you want lingering comfort, look at high-back club styles and add a seat pad.

Which One Should You Buy?

For one box that fills a four-person table, the SAILARY four-pack with its stated 350 lb capacity is the easy starting point. If you want arms and a metal frame, the DAYARUS set is the sturdier-looking option. For small patios where storage is the issue, choose the UDPATIO or JEAREY stackers, and pick Tangkula if you prefer wood armrests. A balcony pair is simplest with the VOYSIGN set of 2. Wherever you land, measure your table first, confirm the seat height, and read the cushion care tag before checkout.

Sources

• Manufacturer product listings for each model named above
• Outdoor furniture sizing guidance on seat and table heights
• Maker care guidance for resin wicker and powder-coated frames
• Textile industry descriptions of solution-dyed and UV-resistant outdoor fabrics

Last updated: November 2026