February 25, 2014
Today Homebestfurniture.com will share to you how to Waterproofing Your Deck with easy steps to implement. Usually Water, when combined together with UV radiation and changes in climate and heat range, can easily create your deck to look dull plus weathered by washing away your deck’s finish, natural resins, and color. Whilst you can’t perfectly lessen your deck’s exposure to the factors, sealing your deck will help maintain its finish, which may keep you time and money.
Seal your deck now to maintain it looking its better. First, prevent by your local True Value hardware store for the tools, products, and expert advice you require to keep your water heater in tip-top shape.
Is your deck almost all gray and it does not appear as nice as it once did? Have you ever thought about if there was a way to water-resistant it so that it lasts much longer and does not weather as fast? Did you ever wonder if you could do it yourself without expensive labor? If you answered yes to any of these issues, keep learning because I am going to help you learn how to waterproof your deck.
Many of the weather of a wood deck occurs mainly because of two things: Sunlight and Water. Sunlight is what breaks down the original rich colors. Combined with rain or snow, the sunlight will infiltrate deeper over time. So when you work on waterproofing the deck, the waterproofing material you choose should also protect against Ultraviolet, or UV, light.
Excessive moisture in your deck potentially leads to the break down of the wood with rot and – based on your climate – insect infestation. During you waterproof your deck, if you can, be sure to seal below as well. Many sealants say they last 2 to 5 years, but I find when I waterproof my wood deck, I need to do it nearly every year due to my location’s harsh climate.
Right here is a list of things you will need to get started:
-A wood deck cleaner
-A hand pump sprayer or other kind of sprayer
-A few normal paint brushes
-A power washer (either purchased or rented)
-A few cans of deck waterproofing sealant
-A roller paint brush with long handle
First, use the power washer to rinse off any debris and to take off that first layer of dirt and grime. You would not like to negotiate any dirt into the wood. Next, take the directions of the wood cleaner. Make sure to check the weather forecast, mainly because at this point you commonly need to wait two or three days for anything to dry out again.
Then, put your waterproofing sealant into your sprayer and get your roller paint brush prepared. The reasons you need a long handle is so you are not folding over all the time. Doing work your way around your deck, first spray a section with the sealant and then use the roller brush to function the sealant into the wood. Do this first on your whole deck. Railing and steps often want to be finished separately with a normal paint brush, alternatively you end up spraying sealant onto the deck or into the grass.
Action 1. Check Your Deck
There are a couple of tests you can perform to see if your deck needs waterproofing. Drop several drops of water onto the deck. If the water beads up, the deck is still secured and doesn’t need to be waterproofed now. If a drop soaks into the wood, it signifies the old finish or waterproofing layer has worn away leaving the wood unprotected. You can also firmly press a piece of tape against the surface to be stained. The presence of old stain or wood fibers on the tape could suggest a potential moisture problem. Remove eroded wood fibers and reduce stain by using a wood stripper then sanding and power washing the surface.
If your deck looks faded and gray, it’s time to refinish with some coats of stain. See the project, Stain Your Deck for more tips and information on how to finish your deck. Almost all stains are waterproofing sealants as well, enabling you to stain and seal in one step. If it’s time to refinish your deck, see using a quality stain, such as Woodsman.
Prior to you start staining or sealing, check your local weather report to be sure you’ll have at least 48 hours of dry weather.
All stains protect wood from moisture, but many offer better protection from UV rays. Clear stains only protect wood, while pigmented stains provide a higher degree of UV protection.
Also, check your deck for wood that’s worn out, splitting, twisting or rotting. If you see these signs, you will need to do more prep work and refinish the deck, before waterproofing.
Step 2. Organize the Deck for Waterproofing
Before you start, remove everything from the deck like furniture and potted plants. Freely cover any delicate or fragile ground plants adjacent to the deck through tarps or drop cloths. Never use plastic sheeting on shrubs and plants. It can make a deadly “greenhouse effect” and harm your plants. Get rid of drop cloths from your foliage immediately after your project is finish so they don’t suffocate. Sweep off loose debris with a broom and clean around the cracks using a slender stick or tool. Maintenance damaged boards and hammer in popped-up nails.
Make use of a garden hose or a pressure level washer to spray the surface of the deck, forcing away dirt, dust, oil and grease. This will additionally help eliminate the top layer of previous waterproofing. Begin at one end of the deck and continue until you have rinsed the entire surface and eliminated as much dirt as achievable. If you use a pressure washer, maintain the pressure set to less than 1,000 pounds per square inch and leave a few feet between the spray nozzle and the deck to avoid damaging the wood.
Set it to spray a fan of water so it pushes dirt and debris away faster. Spray between the deck boards to prevent any remaining debris. Use a pole sander or orbital sander with medium-grit sandpaper to smooth down any splintered areas and to remove remnants of the previous layer of sealant. Starting with as clean a surface as possible will help the new coat of sealant set in and provide a better level of protection.
When making use of a pressure washer, use safety glasses to protect your eyes from splashing water and debris.
Cleanup your deck at least once a year helps it last longer and looks better while maintaining the integrity of the wood. And when you’re planning on sealing or refinishing your deck, you’ll have to clean it first. Deck cleaning products are available in a variety of types and strengths. A few offer a special chlorine bleach formula for eliminating mold, mildew and algae. Nevertheless, chlorine bleach formulas may require more continual cleanings. Choose using a non-chlorine bleach cleaner instead, like Woodsman Premium Wood Cleaner.
The most ideal outdoor temperature for cleaning and dealing with your deck is anywhere between 50 and 90 degrees Fahrenheit.
Make sure your deck is compatible with the cleaner you pick, especially, if your deck is crafted of soft wood like redwood or cedar. Check the manufacturer’s instructions to see whether or not you need to get started with a dry or wet deck.
Your can try to wash on a calm day to maintain wind from blowing the cleaning agent around the garden. Use a deck stain applicator to utilize the cleaner to the entire deck. Whilst applying, be careful not to enable the cleaner to puddle wherever on your deck to assure an even looks.
Scrub tough areas with a stiff brush or a broom. Don’t choose wire brushes as wire bristles can easily break off into the wood and cause rust spots. Follow the product’s instructions with regards to how long to let the cleaner soak into the wood, usually about 10 to 15 minutes. After the cleaner has been allowed to soak, rinse the deck completely with a hose.
Cleansers have bleaching agents, so that wear protective clothing, safety goggles and rubber gloves.
After cleaning your deck, let it dry for at least 24 hours.
Step 3. Utilize Sealant
Use a thin, even coat of high-quality, mold- and mildew-resistant, waterproof sealant with UV protection, such as Woodsman® Water Repellent or Woodsman® Wood-Toned UV Wood Sealer and Protector, using a stain brush, in the direction of the boards. Don’t disregard to cover corners and other hard areas such as steps, railings, board ends and cracks. Apply two coats if needed.
Basic Safety Warn!
Wear protective clothing, safety goggles and rubber gloves when sealing your deck to protect against skin irritation.
Never apply sealant in direct sunlight. It will dry too quickly without absorbing into the wood.
Action 4. Finish Up
Stay off the deck while it dries, for at least 48 hours. Permit the sealant to dry completely when substituting any furniture and potted plants. When you’re finished, remove your drop cloths, return furniture and other items to your deck, clear your equipment and enjoy.
That’s it! Your deck is sealed, waterproofed and well prepared for the winter weather ahead. For the rest of your plans, always visit your local True Value hardware store for the tools, products and expert advice you need to start right.